Wood finishing Totally Explained

Everything about Wood Finishing totally explained

Wood finishing refers to the process of embellishing and/or protecting the surface. The process starts with surface preparation, either by sanding by hand (typically using a sanding block or power sander), scraping, or planing. Imperfections or nail holes on the surface may be filled using wood putty or pores may be filled using wood filler. Often, the wood's colour is changed by staining, bleaching, ammonia fuming and a number of other techniques. Some woods such as pine or cherry don't take stain evenly, resulting in "blotching". To avoid blotching, a barrier coat such as shellac or "wood conditioner" is applied before the stain. Gel stains are also used to avoid blotching. Once the wood surface is prepared and stained, a number of coats of finish may be applied, often sanding between coats. Commonly used wood finishes include wax, shellac, drying oils (such as linseed oil or tung oil), lacquer, varnish, or paint. Other finishes called "oil finish" or "Danish Oil" are actually thin varnishes with a relatively large amount of oil and solvent. Water-based finishes can cause what is called "raising the grain" where surface fuzz emerges and requires sanding down.
Finally the surface may be polished or buffed using steel wool, pumice, rottenstone and other polishing or rubbing compounds depending on the shine desired. Often, a final coat of wax can be applied over the finish to add a slight amount of protection. French polishing isn't polishing as such, but a method of applying many thin coats of shellac using a rubbing pad, yielding a very fine glossy finish.
Different tools used to apply wood finishes include rags, rubbing pads, brushes, and spray guns. The processes involved and the terminology for the materials used are quite different in Britain than the processes and terms used in the USA. For instance, the process of replicating the look and feel of traditional French polished wood is more commonly done in the UK by "pulling over" precatalysed lacquer, within 24 hours of spraying, whereas in the US a "rubbed" finish is more common.

Comparison of different clear finishes as used in America

wood varnish is a great way to make your work look nice. Choosing a clear finish for wood involves trade-offs between appearance, protection and durability, safety, ease of application, reversibility, and rubbing qualities. The following table compares the characteristics of different clear finishes. "Rubbing qualities", a term of art, indicates the ease with which the finish can be sanded between coats. It doesn't indicate a method of application such as brush or rag.

	ppearance	rotection	urability	afety	ase of Application	eversibility	ubbing Qualities
Wax	Creates shine	Great	Lasts forever	Safe when solvents in paste wax evaporate	Applied with steel wool, needs sanding	Can easily be removed with solvents	Needs to be buffed
Shellac	Some yellow or orange tint, depending on grade used	Fair against water, good on solvents except alcohol	Durable	Safe when solvent evaporates, used as food and pill coating	French polishing difficult technique to master.	Completely reversible using alcohol	Excellent
Nitrocellulose lacquer	Transparent, good gloss	Good protection	Hard and durable	Uses toxic solvents, including toluene. Breathing protection is needed, especially if sprayed	Requires spray equipment. Brush-on products also available	Completely reversible using lacquer thinner	Excellent hard finish
Conversion lacquer	Transparent, good gloss	Excellent protection against many substances	Hard and durable	Uses toxic solvents, including toluene. Breathing protection is needed, especially if sprayed	Requires spray equipment. Used in professional shops	Difficult to reverse	Excellent hard finish
Linseed oil	Yellow warm glow, pops grain¹, darkens with age	Very little	Fairly durable, depending on number of coats	Relatively safe, metallic driers are poisonous	Easy, apply with rags and wipe off. Takes relatively long time to dry	Needs sanding out as oil is absorbed	None
Tung oil	Warm glow, pops grain¹, lighter than linseed	Very little	Fairly durable, depending on number of coats	Relatively safe, metallic driers are poisonous	Easy, apply with rags and wipe off. Faster to dry than linseed oil	Needs sanding out as oil is absorbed	None
Alkyd varnish	Not as transparent as lacquer, yellowish/orange tint	Good protection	Durable	Relatively safe, uses petroleum based solvents	Brush or spray. Brushing needs good technique to avoid bubbles & streaks	Can be stripped using paint removers	Fair
Polyurethane varnish	Transparent, many coats can look like plastic	Excellent protection against many substances, tough finish	Durable	Relatively safe, uses petroleum based solvents	Brushing needs good technique to avoid bubbles & streaks	Can be stripped with difficulty using paint removers	Bad, coats don't meld leading to white rings if rubbing out cuts through coat
Water-based polyurethane	Transparent, may give cold bluish tinge to wood	Good protection	Durable	Safer than oil-based, fewer volatile organic compounds (VOCs)	Brush or spray. Brushing needs good technique to avoid bubbles & streaks	Can be stripped with difficulty using paint removers	Bad, coats don't meld leading to white rings if rubbing out cuts through coat
Oil-varnish mixes	Similar to oils unless many coats applied, then takes on characteristics of varnishes	Low, but more than pure oil finishes	Fairly durable, depending on number of coats	Relatively safe, uses petroleum based solvents	Easy, apply with rags and wipe off. Faster to dry than linseed oil	Needs sanding out as oil is absorbed	None unless many coats applied

1 - accentuates visual properties due to differences in wood grain yeah thats all.

Automated Wood Finish Application

Manufacturers who mass produce products implement automated flatline finish systems that run a on a conveyor belt that first begin by being sanded, then dust is removed, and the wood finish is applied via spray gun. The material then can enter an oven or be sanded again depending on the manufacturer’s setup. The material can also be re-entered into the assembly line to apply another coat of finish depending on the manufacture.

References

Michael Dresdner (1992). The Woodfinishing Book. Taunton Press. ISBN 1-56158-037-6
Bob Flexner (1994). Understanding Wood Finishing: How to Select and Apply the Right Finish. Rodale Press ISBN 0-87596-566-0

Further Information

Get more info on 'Wood Finishing'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://wood_finishing.totallyexplained.com">Wood finishing Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.